Water Right IMP-1054 Guia de Resolução de Problemas

Impression Series® and Impression Plus Series®Water FiltersFor Models:• IMBF• IMBF-MAN• IMAN• IMAF-MGS• IMS• IMB• IAG• IACG-AN• IMPBF• IMPBF-MAN• IMPA

10OPERATING DISPLAYS AND INSTRUCTIONS:1. GENERAL OPERATION: When the system is operating, one of three displays may be shown. Pressing next will alte

115. ERROR MESSAGE: If the word “ERROR” and a number are alternately flashing on the display record the number and contact the dealer for help. This

121. Check the media height by shining a flashlight through the tank to see the height of the mineral. If the level is not seen, the top fill plug wi

13 PROBLEM CAUSE CORRECTION 1. No display on PC board A. No power at electric outlet A. Repair outlet or use working outlet B. Control valve po

7. Control valve does not regenerate automatically but does when the correct button(s) is depressed and held. For timeclock valves the buttons are

15 12. Control valve fails to draw in regenerant A. Injector is plugged A. Remove injector and clean or replace B. Faulty regenerant piston B.

16 16. E3, Err – 1003, Err – 103 = Control valve motor ran too long and was unable to find the next cycle position A. Motor failure during a regener

17REPLACEMENT PARTS:2713546FRONT COVER AND DRIVE ASSEMBLYItem No. Part No. Description Qty.1CV3540-A Black Impression® cover 1CV3540-W-A Gray Impres

6810117 97 12423511314NOTE: For Impression Plus® Models only. Not available on 1¼ " valve.REPLACEMENT PARTS:For Impression Plus® Models OnlyPI

19REPLACEMENT PARTS:BYPASS VALVE Item No. Part No. Description Qty.1 CV3151 Nut, 1” quick connect 22 CV3150 Split ring 23 CV3105 O-ring 215 24 CV31

TABLE OF CONTENTSPreinstallation Instructions for Dealers ...3Bypass Valve ...

INJECTOR ASSEMBLIESItem No. Part No. Description Qty.1CV3176 Injector cap 12CV3152 O-ring 135 13CV3177-01 Injector screen 14CV3010-1Z Injector ass

21REPLACEMENT PARTS:DRAIN LINE ASSEMBLY 3/4”Item No. Part No. Description Qty.1 CH4615 Elbow locking clip 12 CPKP10TS8-BULK Optional insert, 5/8” tu

REPLACEMENT PARTS:Although no tools are necessary to assemble or disassemble the valve, the Service Wrench, (shown in various positions on the valve)

231” PVC MALE NPT ELBOWItem No.Part No. Description Qty.CV3007 1” PVC male NPT elbow assembly 21 CV3151 Nut, 1” quick connect 22 CV3150 Split ring

1-1/4” & 1-1/2” PVC SOLVENTItem No.Part No. Description Qty.CV3007-07 1-1/4” & 1-1/2” PVC solvent assembly 21 CV3151 Nut, 1” quick connect 2

25ACID NEUTRALIZERSBACKWASHING FILTERSIRON FILTERSMineral Type Calcite or Mix Calcite or Mix Calcite or Mix Calcite or Mix Calcite or Mix Calcit

26WidthHeightSULFUR AND IRON AIR FILTERSMineral Type Catalytic Carbon Catalytic Carbon Catalytic Carbon Birm Birm BirmAmount (Cu Ft) 1.0 1.5 2

27Water Conditioner Limited WarrantyCongratulations. You have purchased one of the nest water treatment systems available. In the unlikely event of a

1900 Prospect Court • Appleton, WI 54914Phone: 920-739-9401 • Fax: 920-739-9406MANUAL REGENERATIONNOTE: If you need to initiate a manual regenerat

PREINSTALLATION INSTRUCTIONS FOR DEALERS:3The manufacturer has preset the water treatment unit’s sequence of cycles and cycle times.The dealer should

4The bypass valve is typically used to isolate the control valve from the plumbing system’s water pressure in order to perform control valve repairs o

5GENERAL INSTALLATION & SERVICE WARNINGSThe control valve, fittings and/or bypass are designed to accommodate minor plumbing misalignments. There

6 When installing an air regenerating filter the customer may experience, under certain conditions, small amounts of air (cloudy water) at the tap

78. CHECK VALVE: All air systems include an internal check valve and screen assembly as part of the air draw system (see diagram at right). This chec

8Time of day should only need to be set after extended power outages or when daylight saving time begins or ends. If an extended power outage occurs,

STARTUP INSTRUCTIONS:9FLUSHING OF SYSTEM:To flush the system of any debris and air after installation is complete, please perform the following steps: